The short answer
Heat pump installation in Inglewood starts with a load calculation and a check of your ductwork and electrical panel, followed by choosing a ducted or ductless system that fits the house. Rebates depend on which utility serves your address, and the federal 25C tax credit no longer applies to systems installed after December 31, 2025.
A heat pump heats and cools your home with one electric system. For many Inglewood homeowners it replaces both an aging gas furnace and a worn-out air conditioner in a single project. AirEdge HVAC Repair Service installs heat pumps in homes across Inglewood, including ZIP codes 90301, 90302, 90303 and 90305. Our base in Los Angeles is about 4 miles east, so scheduling site visits and installation days is straightforward. This page covers how we size and plan an installation for your home, which rebates may apply at your address, and what to know if your current furnace is near the end of its life.
Why Inglewood Homeowners Are Switching to Heat Pumps
Los Angeles has a Mediterranean climate with dry summers and mild winters. That suits heat pumps well. On most heating days the system runs efficiently, and in summer the same equipment provides air conditioning. Fall Santa Ana winds can bring hot, dry spells, so cooling capacity matters even after summer ends.
Air quality rules are another reason. South Coast AQMD Rule 1111 limits NOx emissions from natural-gas fan-type central furnaces sold and installed in the Los Angeles region. The district has been amending the rule toward zero-emission requirements. If you're planning to replace a gas furnace, check the current rule before you buy, because the district sets and revises the compliance dates. A heat pump avoids that question entirely.
How We Plan an Installation for Your Home
We don't size a heat pump by matching the old unit's tonnage. Before we recommend equipment, we look at the house itself.
An oversized system short-cycles and controls humidity poorly. An undersized one runs constantly on the hottest afternoons. Getting the planning right protects comfort and efficiency for years.
- A room-by-room load calculation based on square footage, insulation, windows and sun exposure
- The condition, sizing and sealing of existing ductwork, if the home has it
- Electrical panel capacity and whether a new circuit or panel work is needed
- Where the outdoor unit can sit, with attention to airflow, noise and setbacks from property lines
- Where your thermostat is and whether it can control a heat pump properly
Ducted and Ductless Options
If your home already has a forced-air furnace with ducts in good shape, a ducted heat pump can often use that system. The outdoor unit replaces the AC condenser, and an indoor air handler or coil connects to the existing ducts. Leaky or undersized ducts should be repaired first, or the new system won't perform as rated.
Homes heated by wall furnaces, or with no central air at all, are often better served by ductless mini-splits. Each indoor head serves one room or zone, so you can heat or cool only the spaces you use. Additions and converted garages are common candidates. We'll explain the tradeoffs in cost, appearance and comfort for your specific layout.
Rebates: LADWP, SCE and Federal Credits
Many homes outside the City of Los Angeles are served by Southern California Edison rather than LADWP. Which equipment rebates you can get depends on the utility that serves your address. We confirm the current offer for your home before quoting it.
If your address is an LADWP residential electric account, you can apply for Consumer Rebate Program rebates on qualifying heat pump systems. The amount is based on the unit's SEER2 and HSPF2 ratings. You file the application after the equipment is purchased and installed, within 12 months of purchase, so keep your invoice and equipment details.
The federal Energy Efficient Home Improvement Credit (25C) covered qualifying heat pumps placed in service before December 31, 2025. It is not available for installations after that date, so don't count on it when budgeting a new system.
What Installation Day Looks Like
Most installations follow the same sequence. We protect floors and work areas, then remove and dispose of the old equipment. Next we set the outdoor unit and indoor components and run refrigerant lines and electrical connections. Before turning the system on, we pressure-test and evacuate the refrigerant lines.
Then we start the system and check refrigerant charge, airflow and temperatures in both heating and cooling modes. Before we leave, we walk you through the thermostat and show you how to change filters. We also serve Hawthorne, Lawndale, Gardena, Huntington Park and Compton, if you're helping a neighbor or family member plan a similar project.
More services in Inglewood
- AC Repair in InglewoodLocal service & repairs
- Heating Repair in InglewoodLocal service & repairs
- AC Installation in InglewoodLocal service & repairs
- Furnace Repair in InglewoodLocal service & repairs

